Bridges

Notice

Solid objects built to safely cross rivers.

Survey

Survey will give you information on where the other character is standing regarding distance, direction and height difference.

To survey for a bridge two characters are needed. One character must carry a range pole, the other a dioptra. The lowest quality of the two items determines how long a bridge is that you can survey.'

The character with the range pole does not have to do much besides holding the range pole. To do this activate the range pole, click the ground and select Hold from the menu. When the action timer starts face the character with the dioptra.

The character with the dioptra will do the actuall survey. Activate the dioptra, right click the player holding the range pole and select Survey from the menu.

The planning process will print messages in the event log

You pack up the dioptra.
You carefully place the dioptra on its tripod in front of you.
You make sure the dioptra is level.
You point the dioptra at <other player>.
You wave at <other player>.
You line up the dioptra with <other player>.
You look through the dioptra.
You focus on the range pole.
You read the graduations on the range pole and work out the height difference.
<other player> is <x> tiles <direction> of you. Also you appear to be <x> dirt higher than <other player>.
You stop surveying.
You pack up the dioptra.

Building

To plan a bridge two characters are needed. One character must carry a range pole, the other a dioptra.

The character with the range pole does not have to do much besides holding the range pole. To do this activate the range pole, click the ground and select Hold from the menu. When the action timer starts face the character with the dioptra.

The character with the dioptra will do the actuall bridge planning. Activate the dioptra, right click the player holding the range pole and select Plan bridge from the menu. Standing right in front of the other character will create a 1 tile wide bridge. Standing at an offset will create bridges multiple tiles wide.

The planning process will print messages in the event log

You carefully place the dioptra on its tripod in front of you.
looks like bridge would be <'width'x'length'> (East-West)
The tile border to your <direction> is level
You make sure the dioptra is level.
You point the dioptra at <other player>.
You wave at <other player>.
You line up the dioptra with <other player>.
You look through the dioptra.
You focus on the range pole.
You read the graduations on the range pole and work out the height difference.
The tile border to your helpers <direction> is level
You check the heights of the plan ends.
<Height difference>.
You work out the orientation and width for the bridge.
You check for clearance between the bridge ends.
You check for protruding foliage.
You check for nearby cave entrances and any lava.
You check for any items in the way.
You check that you have permissions to build the bridge.
You check for any bridges that may interfere with this bridge.
You check there would be no buildings under this bridge.
You work out the styles of bridges that would fit.
You start working out the bridge components required.
Planned bridge area is <x> tiles long and <y> tile wide.
(23:ESabFFFFFFFFFFFFFFFBASE)
You stop surveying.
You pack up the dioptra.

When all requirements are met you are presented with list of possible bridges.

The selection depends on planned width, length, height difference and clearance below the planned bridge.

If you have choosen a flat bridge that is longer than 5 tiles then you have the possibility to change the schematic of your bridge plan.

When you have choosen a type of bridge you can name the planned bridge and select the steepness of the bridge if you've choosen an arched bridge.

After clicking Finalize a wooden frame for the bridge is constructed.

For each tile of the bridge a bridge segment has to be completed in multiple stages. Those are 'abutments' for the out segments, 'bracing' and 'floating' for stone bridges and 'crown' for rope and wood bridges.

Until the bridge has been completed no other bridge can be started by the character.

Skill Requirements

Here is a table of the required skill to plan bridges (by length and material)

Required skill by length and material

Type\Length	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24	25	26	27	28	29	30	31	32	33	34	35	36	37	38
Wood	10	23	29	34	38	41	44	47	50	52	55	57	59	62	64	66	68	70	72	74	76	77	79	81	83	85	86	88	90	92	93	95	97	99
Rope	10	23	29	34	38	41	44	47	50	52	55	57	59	62	64	66	68	70	72	74	76	77	79	81	83	85	86	88	90	92	93	95	97	99
Brick	30	40	45	48	51	54	56	59	61	63	65	66	68	70	72	73	75	76	78	79	81	82	84	85	86	88	89	90	92	93	95	96	97	99
Marble	40	49	53	56	58	60	63	64	66	68	70	71	73	74	75	77	78	79	81	82	83	85	86	87	88	89	90	92	93	94	95	96	97	99
Arched Brick	50	57	60	63	65	67	69	70	72	73	74	76	77	78	79	81	82	83	84	85	86	87	88	89	90	91	92	93	94	95	96	97	98	99
Arched Marble	60	66	68	70	72	73	75	76	77	78	79	80	81	82	83	84	85	86	87	88	88	89	90	91	92	92	93	94	95	95	96	97	98	99

Note to build any bridge section, the skill requirement is:

Required skill by material

Type	Skill
Wood	10	Carpentry
Rope	10	Rope Making
Brick	30	Masonry
Marble	40	Masonry
Arched Brick	30	Masonry
Arched Marble	40	Masonry

When making the Rope Bridge, how much they sag is based on your character strength with options ranging from 3% to 12% sag.

Rope Bridge sag (3%-12%)

Body Strength	Sag %
1	12
10	11
20	10
30	9
40	8
50	7
60	6
70	5
80	4
90	3

Notes

• Some Bridge info may be found in the week 43 news post here: http://forum.wurmonline.com/index.php?/topic/112518-news-update-work-and-progress-week-43/
• Bridge material calculator located here: http://forum.wurmonline.com/index.php?/topic/122044-bridge-material-calc/

• Each house floor is calculated as 32 dirt slope, you need to be higer from water level for arched bridge atlast 8 slope.

See also

• Rope Bridge
• Wood Bridge
• Brick Bridge
• Marble Bridge
• Landbridges
• Dioptra
• Range pole